Jun 30, 2008
My Digital Life Editorial Team

How to Change or Spoof MAC Address in Windows XP, Vista, Server 2003/2008, Mac OS X, Unix and Linux

MAC address (Media Access Control address) is a quasi-unique identifier consists of a six byte number that attached to most network adapter card or network interface card (NIC). As such, all network cards, whether it’s of Ethernet NIC, Gigabit Ethernet NIC or wireless 802.11a/b/g/n WiFi or HiperLAN adapter, should have different MAC addresses, which also known as Ethernet Hardware Address (EHA) or adapter address.

In operating system, MAC address is often represented in 12-digit hexadecimal number. For example, 1A-2B-3C-4D-5E-6F. In practical usage, layer 2 MAC address is converted from layer 3 protocol addresses such as Internet Protocol (IP address) by ARP (Address Resolution Protocol), which then allowed each host to be uniquely identified and frames to be marked for specific hosts on broadcast networks, such as Ethernet. After translated (or when a host on LAN sends its MAC address to another machine which does n ot configured not to accept unrequested ARP replies on the network for preemptive caching), MAC address is cached on source PC ARP table for later use. Content of ARP table on each computer can be viewed by typing arp -a in Windows or arp in Linux. MAC address thus forms the basis of most of the layer 2 networking upon which higher OSI Layer protocols are built to produce complex, functioning networks.

There are many reasons or possibilities that an user may want to change the MAC address or a network adapter, which also known as MAC spoofing. For example, to bypass the MAC address filtering on firewall or router. The trick can be used to get pass the network access restriction by emulating a new unrestricted MAC address, or to gain access connection by spoof an authorized MAC address after sniffing the legitimate MAC address out of the air in MAC filtering Wi-Fi network.

Beside, hackers or enthusiasts also spoofing another host’s MAC address as their own in order to receive traffic packets not meant for them, although ARP poisoning technique is more commonly used. However, changing MAC address can still keep the real information from been detected and logged by various services such as IDS, firewall, DHCP server, wireless access points and etc, and is essential protect user’s privacy. MAC spoofing also potentially trigger a Denial of Service (DoS) attack by causing routing problem with duplicating MAC address exists in the network, especially those similar with gateway and AP router’s BSSID (Basic Service Set Identifier.)

Whatever the reason, it’s pretty easy to change the MAC address or perform MAC spoofing on most of today’s hardware, listed below. Actually, the original MAC address is burnt and imprinted to the network card, and cannot be changed. However, operating system can spoof as if there is different MAC address for the network interface card using tricks below.

Change the MAC address in Windows

  1. Go to Start -> Control Panel. Double click on Network Connections (inside Network and Internet Connections category in Windows XP). The, right click on the active network connection with network adapter that you want to change the MAC address (normally Local Area Network or Wireless Network Connection) and click on Properties.

    Above steps work in Windows XP, Windows 2000 and Windows Server 2003. For Windows Vista, access to NIC’s properties is from Control Panel -> Network and Internet -> Network and Sharing Center -> Manage Network Connections.

    Alternatively, if you already know which network adapter that’s responsible for your network or Internet connection, go to Device Manager and open the properties dialog by double click on the NIC itself.

  2. In the General tab, click on the Configure button.
  3. Click on Advanced tab.
  4. In the Property section, select and highlight Network Address or Locally Administered Address.
  5. To the right, “Not Present” radio button is by default selected as value. Change the value by clicking on radio button for Value:, and then type in a new MAC address to assign to the NIC.

    Change MAC Address of Network Adapter

    The MAC address consists of 6 pairs of numbers (0 – 9) and characters (A – F) combination. For example, 88-17-E8-90-E2-0A. When entering the new MAC value, omit the dash (-), for example 8817E890E20A.

  6. Click OK when done.
  7. To verify the change of MAC address, go to command prompt, then type in one of the following commands:

    ipconfig /all
    net config rdr

  8. Reboot the computer if successful to make the change effective.

Note: To restore or reset back to original default MAC address, simply set back the option to “Not Present”.

Change the MAC Address of NIC in Windows via Registry

  1. Open a command prompt.
  2. Type the following command and hit Enter.

    ipconfig /all

  3. Record down the Description and the Physical Address (is MAC address) of the active network connection (discard those with Media Disconnected state).

    Get MAC Address for Network Card

    For example, in figure above, Description is Intel(R) Wireless WiFi Link 4965AGN and MAC address is in the format of 00-XX-XX-XX-XX-XX.

  4. In the command prompt also, type the following command and hit Enter.

    net config rdr

  5. Record down the GUID for the MAC address for the active connection’s NIC which MAC address to be changed. The GUID is contained within the { and } brackets right in front of the MAC address as shown in figure below.

    GUID for the NIC

  6. Type regedt32 or regedit in Start -> Run box or in Start Search for Windows Vista. Note: for Windows NT 4.0 and Windows 2000, regedt32 must be used.
  7. Navigate to the following registry key:


  8. Expand the {4D36E972-E325-11CE-BFC1-08002BE10318} tree, and there will be more sub-keys in the form of 0000, 0001, 0002 and so on.
  9. Go through each sub-key starting from 0000, look for subkey that has DriverDesc value data that matches NIC description copied from step above, that want its MAC address to be changed. In most cases, it will be similar to the network adapter card name.

    To verify that the subkey found is indeed a correct one, check the value of the NetCfgInstanceId, which should have the same value with the NIC’s GUID taken from step above.

  10. Once a sub-key is matched to the network interface card that MAC address want to be spoofed, select and highlight the subkey. Right click on the sub-key (for example, 0000), then select New -> String Value. Name the new value name as NetworkAddress.

    Note: If NetworkAddress REG_SZ registry key is already existed in the right pane, skip this step.

  11. The double click on NetworkAddress and enter a new MAC address as its value data.

    Change and Spoof MAC Address in Registry

    Note that the 12-digit MAC address in hexadecimal format, and should be entered without any dash (-). For example, 1A2B3C4D5E6F.

  12. Reboot the system to make the new MAC address effective. Alternatively, if you don’t want to restart the system, try to disable and then re-enable the network adapter in Device Manager.
  13. To verify the change of MAC address, go to command prompt, then type in one of the following commands:

    ipconfig /all
    net config rdr

Note: To restore or reset back to true original hardware burned-in MAC address, remove the NetworkAddress registry key that is been added.

Alternative: Third party tools and utilities to change the MAC address in Windows operating system are plenty, for example: SMAC (direct download link to smac20_setup.ex, supports Windows Vista, XP, 2003, 2000), Macshift (direct download link to macshift.zip, for Windows XP), BMAC (almost identical SMAC MAC changer clone by moorer-software.com), Mac MakeUp (direct download link to macmakeup.zip, for Windows 2000/XP/2003/Vista), MadMACs (MAC Address Spoofing And Host Name Randomizing App For Windows, directly download MadMACs.zip), EtherChange (direct download link to etherchange.exe), and Technitium MAC Address Changer (for Windows 2000 / XP / Server 2003 / Vista / Server 2008).

How to Change MAC Address (MAC Spoofing) in Linux and *nix

To change your MAC address in Linux and most Unix-like (*nix) system, run the following script commands:

ifconfig <interface> down

ifconfig <interface> hw <class> <MAC address>

ifconfig <interface> up

For example, the command looks lik “ifconfig eth0 down hw ether 1A:2B:3C:4D:5E:6F”. First command brings down the network interface, second command change its MAC address while third command bring up the interface again. Note that in some cases, to bring down and bring up the network interface, the following commands have to be used:

/etc/init.d/networking stop or /etc/init.d/network stop (in the case of Fedora Core 5)

/etc/init.d/networking start or /etc/init.d/network stop (in the case of Fedora Core 5)

Alternatively, for Fedora Code 5 Linux with Iproute2 tools installed, the following commands also can change the MAC address to spoofed version:

/etc/init.d/network stop

ip link set <interface> address 1A:2B:3C:4D:5E:6F

/etc/init.d/network start

For example, “ip link set eth0 address 1A:2B:3C:4D:5E:6F”. To check whether the MAC address has been spoofed, use ip link ls eth0 or ip addr ls eth0 instead of using ifconfig eth0.

How to Make the Spoofed MAC Address Permanently Even After Reboot in Linux

Edit the ifcfg-eth0 file (or other similar file if you’re changing different interface), add the following variable line to the file:


Then run service network restart to make the change effective immediately.

How to Make the Spoofed MAC Address Permanently on Restart in Debian

Edit the /etc/network/interfaces file and add in the following variable line to the appropriate section so that the MAC address is set when the network device is started.

hwaddress <interface> 02:01:02:03:04:08

For example, “hwaddress ether 02:01:02:03:04:08”.

Alternative: GNU Mac Changer (for Debian, Slackware, ArchLinux, Mandrake, Crux and other RPM-based distributions such as Fedora, Red Hat, CentOS, ASPLinux, SUSE Linux, OpenSUSE and etc.

How to Change MAC Address (MAC Spoofing) in BSD or FreeBSD

Issue the following commands in shell:

ifconfig <interface> down

ifconfig <interface> <class> <MAC address>

ifconfig <interface> up

First command brings down the network interface (optional), second command change its MAC address while third command bring up the interface again (optional). For example, the command looks lik “ifconfig xl0 link 1A:2B:3C:4D:5E:6F” or “ifconfig fxp0 ether 1A:2B:3C:4D:5E:6F”

How to Change MAC address in Solaris

The shell command to change the MAC address in Sun Solaris is as below:

ifconfig <interface> <class> <address>

For example, the command looks like “ifconfig hme0 ether 1A:2B:3C:4D:5E:6F”. Note that the change is temporary that does not persist after a reboot. To make this change permanent, the command can be placed in a runtime control script (/sbin/sh).

How to Spoof MAC Address in HP-UX

It’s possible to change MAC address using HP-UX SAM. Select Networking and Communications, then selecting the interface, then click on Action -> Modify -> Advanced Options. Finally, change the value of station address, which is MAC address name in HP-UX.

How to Spoof and Change MAC Address in OpenBSD

Use the following command to change MAC Address to spoofed MAC in OpenBSD (after version 3.8):

ifconfig <interface> lladdr <MAC address>

For example, “ifconfig bge3 lladdr 1A:2B:3C:4D:5E:6F”.

How to Change to Spoofed MAC Address Permanently in OpenBSD

To make the MAC address changed at boot before network connection is established, and even before parsing of hostname.* file, edit the /etc/netstart file to add in the following lines before the line of “# Now parse the hostname.* file”:

if [ "$if" = "INTERFACE" ]; then
ifconfig <interface> lladdr <MAC address in format of 00:00:00:00:00:00>

# Now parse the hostname.* file

How to Change MAC Address in Mac OS X

Since Mac OS X 10.4.x (Darwin 8.x) onwards, the MAC address of wired Ethernet interface can be altered in Apple Mac OS X in a fashion similar to the Linux and FreeBSD methods. To do so, type the following command in Terminal.app:

sudo ifconfig en0 ether aa:bb:cc:dd:ee:ff


sudo ifconfig en0 lladdr aa:bb:cc:dd:ee:ff (for Mac OS X 10.5 Leopard)

where en0 is the network interface (numbered from en0, en1, en2 …) and aa:bb:cc:dd:ee:ff is the desired MAC address in hex notation.

Alternative: MacDaddy (download MacDaddyX.dmg, support Airport wireless adapter)

Related Posts

  • In step 5, I can’t find anything like your image. I use Win 7 64. How to pass it?

  • santosh

    m using vista and wireless adapter is Atheros AR5006EG Wireless Network Adapter .but my command prompt shows the older mac address not the changed one.

  • Johnny

    when i change my mac on my xp home sp3 dell, it changes the mac but i lose connection why? can anyone help??

  • Vladimir Georgievsky

    Thanks for the article!

  • stranger

    Lot of sites browsed, but this one helped me a lot !!

    Thai Works fine for CentOS 5…

    Heartily Thank You…



  • Amit

    How to check whether user has change the MAC Address ? So that we can block them by misusing this facility of MAC changing. Is there any tool for identifying the same?

    Please tell me…..

    Amit Bartakke

  • Arthur

    My ISP had found a way to ban a specific computer on a shared internet connection(cyber cafe, or having 2 or more computers at home that using the same internet connection or wifi) because of high traffic usage. Even I disconnect and reconnect to internet and change the INTERNAL IP Address still no go but the other computer is good.

    Now, after I change my MAC address, there's nothing can stop/throttle/or even ban my computer from using high traffic usage. It's really helps me a lot. Thanks.

  • blackman

    hi there!

    this is all about "NIC"

    how about the "DSL MODEM MAC"

    can you change it ?


  • Anon

    Thank you! It worked! I used the first method (in Windows).

  • Nope

    This is not working for 4965AGN you mentioned in your article.

    Is there any solution for this to work in windows 7 ?

  • PM

    This is precisely the detail that I was looking for. I appreciate you time in writing this information.

  • stevan

    working tutorial…thanks…

  • John

    I will try to do this.
    Thanks for sharing.

  • Hi,

    This method working on Vista (and other systems too), but You must install older drivers (version before 12.x). This is, because blocked spoof of mac address in new drivers. Try example driver.

  • felipe1982

    >Just run as administrator and walla.
    It's voilà.

  • felipe1982

    openSUSE 11.3. To make change to MAC address permanently, edit the file /etc/sysconfig/ifcfg-* and edit the variable LLADDR=00:00:00:00:00:00 to be the MAC address that you want. If you do not see LLADDR create it at bottom of file. Save/Reboot. Look to /etc/sysconfig/network/ifcfg.template for examples & ideas.

  • Hello, I tried to use your method but it did not work in vista. I don't know what is the problem but even though I change the mac, when I am seeing in command prompt its not over writing the old mac address. Don't know why?

    I have been working on this since a week and still no luck!!!!!!:-(

  • eduardo sousa

    I forgot my pass word for the wireless
    some way to pick the word pass
    thank you very much

  • misto

    Verry nice, Worked awesome for windows vista. Just run as administrator and walla.

  • wim

    Is there no need to change the hostname too besides the MAC address ?

  • wim

    If you change the MAC address in the registry, does windows keep a log of all changes made ?

  • John Nguyen

    let me show u how to find the the sub-key in {4D36E972-E325-11CE-BFC1-08002BE10318} exactly.

    1. Go to "device manger"

    2. Double click in NIC which u want to change

    3. Enter Details tab

    4. Choose "Driver key" in "Properties", hen u will see the sub-key. in my case, it is {4d36e972-e325-11ce-bfc1-08002be10318}011

    PS: i'm using windows 7 and my wifi NIC doesn't allow to change MAC in "Device Manager". The only way i can do is change MAC in registry



    i LOVE YOU

    ive been trying to change my 4965AGN mac address for a long time from the device manager "network address" option but i don't have it.

    now i changed it from the registry

    thank you so very much ^_^

  • Pingback: Joining the modern century or the ranks of the Zombies? - Page 2()

  • addorrer

    wrangler… i think you need to access the wireless router (if you can) and check from there… other than that i'm not too sure if theres a way to check…

  • addorrer

    moomoo i'm having the same problem… but i'm using the intel wifi link 5100 agn

    however the link below worked to some extent but i'm still unable to get it to spoof to the mac address i want >_<


    any ideas?

    thanx in advanced

  • Wrangler


    Thanks man. That was brilliant.

    COuld you tell me how to check which all ipaddress are present in current network (in wi-fi).


  • Reka

    oooh, one more thing. I tried to use Mac Address Changer from Technitium, but it says it can't install itself because vista Sp2 is not compatible or supported. :((

  • Reka

    I have Vista Sp2, and i can't change the network address because I've got a dell laptop, and it doesn't have anything like network address OR locally administrated address in the property section. I'm staying in a youth hostel and the only way to get to the internet is to type in that 12 character code. i used to have XP on another laptop and it worked fine, but now i can't set that address and of course the manager says it's my problem that i got this laptop.

    any ideas how I should work this out?

  • Pingback: How Likely Are You For Wi-Fi Theft? | PCMech()

  • Pingback: Mike in Real Life » Keeping America Safe From Nothing()

  • THANK YOU VERY MUCH for this tip, it got my Wii working at the hotel with their authentication system. > )

  • Pingback: [Announcement 12/16/08] Public Ban List and more - Page 4 - AionSource.com()

  • dora

    @ aelsea:

    Same situation here (XP Home SP3). You have to follow the procedure "Change the MAC Address of NIC in Windows via Registry" as described above. It is a matter of only a few minutes and it worked perfectly on my computer.

  • The process in step 5 under Win XP only works for the Pro version. The "home" version does not have the "Network Address" option in the Properties window.

    Might want to address that for folks who use the "home" version.

    I'm specifically looking at the screen in Win XP Home with Service Pack 3 (SP3) installed.

    • Jonathan

      It’s not a operating system feature. It’s a feature of the driver. If the driver does not have the tab then it does not have the tab.

  • mmm


    Helpful in getting a Wii online at a hotel without error codes (52230, 52231) due to having to log in and accept a user agreement.

  • moomoo

    This method does not seem to work with Intel 4965AGN wireless network adapter. It seems to have some sort of override back to the hardware mac. Any ideas?

  • Aafaq

    I am using ADSL MODEM. Tell me the way to change mac address of modem. I am not using NIC CArd. So pls dont send me the way to change NIC's MAC. I ma not using NIC Card.Iam not using NIC Card.

    Warm Regards,