使并且關閉IPv6支持失去能力在景色

IPv6 (互聯網協議版本6)是後繼者為IPv4，多數大眾網絡層數協議的最新版為在互聯網使用的分組交換的互聯網絡。 在窗口景色， IPv6充分地被實施默認情況下，并且支持，也安裝并且使能，與最大互聯網協議安全(IPsec)支持為IPv6交通和鑿船蟲挖洞支持為non-IPv6明白的設備。

IPv6不是共同的，作為多數軟件，路由器，調制解調器，并且其他網絡設備不支持湧現和防未來協議。 在旁邊，關閉IPv6支持不影響瀏覽為一般的用戶的互聯網的功能。 因而IPv6和鑿船蟲罐頭和(相當可能)應該是殘疾，如果它是沒在使用保存系統資源。 不同於Windows XP， IPv6在窗口景色不可能被卸載，根據 微軟. 然而， IPv6可以是殘疾。 以下指南在網絡接口卡的具體連接將允許用戶使IPv6失去能力。

1. 去網絡連接文件夾(點擊開關，然後用鼠標右鍵單擊在網絡，精選的物產，然後點擊「經理網絡連接」在任務單塊玻璃)。
2. 您應該看各種各樣的LAN、無線、Bluetooth、高速互聯網和其他網絡連接可利用在景色計算機與網絡適配器描述。 用鼠標右鍵單擊在您要使IPv6接口失去能力和選擇「物產」的網絡連接。

   點擊「在用戶存取控制允許請求提示繼續」。

3. 在旁邊清除複選框 互聯網協議版本6 (TCP/IPv6) 組分在名單在「這連接使用以下項目」箱子之下。

   

4. 點擊OK，當做時。
5. 要重新授權給IPv6，滴答作響複選框。

這個方法在特殊LAN接口和連接使IPv6失去能力。 為其他網絡適配器或連接，用戶必須重覆步使IPv6失去能力。 在旁邊，功能失效IPv6在隧道接口或IPv6回送接口也不使IPv6失去能力。

通過景色系統登記使IPv6和鑿船蟲失去能力也是可能的。 登記設置在窗口景色也允許用戶有選擇性地使組分失去能力和配置行為為IPv6。

1. 打開登記編輯(regedit)。
2. 駕駛對以下登記關鍵分支：

   HKEY_LOCAL_MACHINE \系統\ CurrentControlSet \
服務\ tcpip6 \參量\

3. 創造以下登記價值(DWORD類型) ：

   DisabledComponents

   注意名字必須確切地是如所示，包括資本化。 默認情況下DisabledComponents被設置到0。

4. DisabledComponents登記價值是控制旗子以下系列的位屏蔽，從最低位開始(被咬住0)。 To determine the value of DisabledComponents for a specific set of bits, the process is complicated, were hexadecimal value is calculated from binary number of the bits in correct position. For convenient, the following table lists some common configuration combinations and the corresponding DWORD value of DisabledComponents.
   

   Configuration combination	DisabledComponents value
   Disable all tunnel interfaces	0×1
   Disable 6to4	0×2
   Disable ISATAP	0×4
   Disable Teredo	0×8
   Disable Teredo and 6to4	0xA
   Disable all LAN and PPP interfaces	0×10
   Disable all LAN, PPP, and tunnel interfaces	0×11
   Prefer IPv4 over IPv6	0×20
   Disable IPv6 over all interfaces and prefer IPv4 to IPv6	0xFF

   As seen from table above, to disable IPv6 support globally on all interface, set the value data for DisabledComponents to 000000FF, or simply FF. The registry entry will look like below:

   
[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip6\Parameters]
“DisabledComponents”=dword:000000ff


5. Restart the computer for changes to take effect.
6. To revert and enable IPv6, delete “DisabledComponents” registry key or set its registry value to 0.

More ways available to disable Toredo for IPv4 and IPv6 bridge.

IMPORTANT: This is a machine translated page which is provided "as is" without warranty. Machine translation may be difficult to understand. Please refer to original English article whenever possible.

Share and contribute or get technical support and help at My Digital Life Forums.

Related Articles

• How to Disable TCP/IPv6 Teredo Tunneling in Vista
• How to Enable and Turn On Hibernation Feature in Windows Vista
• Temporarily Disable IE7 Protected Mode in Vista on Ad-hoc Basis
• Ways to Turn Off and Disable Vista IE 7 Protected Mode
• How to Disable or Enable Vista User Access Control in Command Prompt
• Disable Compressed (Zipped) Folder Feature in Windows XP and Windows Me
• Disable and Turn Off ClearType Fonts in Windows Vista
• How to Disable and Turn Off Compressed Folder and ZIP Support in Vista (Including Cabinet File)
• Emulate Expanded (EMS) Memory Support in Vista with EMS Magic
• Disable and Turn Off Highlight Newly Installed Programs Feature

This entry was posted on Sunday, September 9th, 2007 at 4:08 pm and is filed under Windows Vista. You can follow any responses to this entry through the RSS 2.0 feed. You can leave a response, or trackback from your own site.