Install and Enable Telnet Server Service in Windows Vista

To accept a incoming Telnet connection, a PC, computer or server must enable and run Telnet Server service which is listening to TCP port 23. By default Windows Vista doesn’t install Telnet Server. The disable of Telnet Server is good practice to minimize security risks. The following guide will install and enable Telnet Server in Vista if you really need it running. Telnet Server in Vista is similar to the one comes with Windows Server 2003, where it provides ASCII terminal sessions to Telnet clients, and supports two types of authentication plus four types of terminals: ANSI, VT-100, VT-52, and VTNT.

How to Enable the Telnet Server Service in Windows Vista

1. Click on Start button, then go to Control Panel -> Programs.
2. Under the Programs and Features section, click Turn Windows features on or off. If User Account Control permission confirmation request warning pops up, click on Continue. If you are prompted for an administrator password, type the password.
3. In the Windows Features dialog box, select (tick) the Telnet Server check box.

   

4. Click OK. Wait for the installation to finish.
5. Go back to Control Panel, then go to System -> Administrator Tools.
6. Click on Services applet (services.msc if you prefer to use Run command or Start Search).
7. Locate the “Telnet” service, right-click on it and select Properties.
8. In the Startup Type drop down menu, select “Automatic” instead of “Disabled”.

   

9. Click on Apply button.
10. Right-click on the “Telnet” service again, but this time select Start option on right click context menu. Telnet Server service should be running after this.
11. Click OK.

After installing Telnet Server Windows feature, instead of going to Services MMC applet, if you prefer you can use elevated command prompt to start Telnet Server, and set Telnet service to run automatically on every system startup. The commands to use are:

1. sc config TlntSvr start=auto

   Set Start Type option to Auto.

2. sc start TlntSvr

   or

   net start TlntSvr

   Start the Telnet Server immediately.

Configuration Options for Telnet Server

As Vista Telnet Server is ported from Telnet Server in Windows 2003, XP and 2000 (W2K), the configuration settings available and how to configure the server are pretty much similar. Generally tlntadmin command is used to administer a local or remote Telnet Server.

For example, you can use tlntadmin command to start, stop, pause or continue Telnet server. Command syntax is:

tlntadmn [\\RemoteServer] [start] [stop] [pause] [continue] [-u UserName-p Password]

The Telnet Server requires NTLM authentication by default. To deactivate and disable NTLM authentication and switch to use only password authentication, use following tlntadmin command:

tlntadmn config sec=-NTLM

Another example command that make Telnet session switch to streams mode in order to make display easier for Unix/Linux clients:

tlntadmn config mode=stream

For more command references visit Microsoft Telnet page.

Related Articles

• Enable and Install Telnet Client in Vista
• Install and Enable SNMP Service in Windows XP, Vista and 2003
• How to Check if Telnet Is Running on a Server
• How to Enable Concurrent Half-Open TCP Connect Attempts Limit in Windows Server 2008 and Vista SP2 or Windows 7
• Telnet for Windows 7 and Windows Vista
• Install or Enable Snipping Tool in Windows Vista
• How to Install KMS Server to Activate Windows Vista Business or Enterprise
• Install and Run IIS (Internet Information Services) Server 7 in Vista
• How to Restart (Stop or Start) cPanel Service (cpsrvd) via Telnet or SSH
• Official Registry Hack Script to Install Windows Server 2008 and Vista SP2 Beta Build 16497 (CPP) via Windows Update

This entry was posted on Monday, August 20th, 2007 at 4:03 pm and is filed under Windows Vista. You can follow any responses to this entry through the RSS 2.0 feed. You can leave a response, or trackback from your own site.